[wiki:Internal/OpenFlow/ return to OpenFlow index]

= Setting up the host for the NetFPGA = 
Here we provide the links and directions followed to set up a working NetFPGA host. The directions can be found on the following site: http://netfpga.org/netfpgawiki/index.php/Guide

== Installing CentOS ==
CentOS is the recommended OS for use with NetFPGA. The most current version is 5.3, which is not listed as a version of CentOS that works with NetFPGA, but was used anyways.  

=== CentOS 5.3 ===
The latest version is CentOS 5.3.  

For the installation, the net install iso was chosen because of its small size. This can be found on any mirror site. 
 * CentOS mirrors : http://isoredirect.centos.org/centos/5/os/i386/
 * Network installation of CentOS : http://www.tonybhimani.com/2007/12/20/centos-51-network-install-instructions/
 
=== CD install of CentOS 5.2 === 
The .iso images can be found here: http://vault.centos.org/5.2/isos/i386/ 
You only need CD's 1 through 4. k3b on Ubuntu was used to burn the images since the images burned with Windows seemed to become corrupt. It seems that you need to manually configure the network interface for eth0. 

 * Network interface configurations: http://www.centos.org/docs/5/html/Deployment_Guide-en-US/s1-networkscripts-interfaces.html
 * VLANs on CentOS: http://www.tummy.com/journals/entries/jafo_20061130_063931
  

Before installing the netFPGA base package, make sure to update the kernel, since the dependencies for NetFPGA software require a newer version of the kernel than the one for 5.3. To install the basic drivers, install teh yum repository and GPG key, followed by the netFPGA base package. 
{{{
rpm -Uhv http://netfpga.org/yum/el5/RPMS/noarch/netfpga-repo-1-1_CentOS5.noarch.rpm
yum install netfpga-base
/usr/local/NF2/lib/scripts/user_account_setup/user_account_setup.pl
}}}
The directions then go over installing CAD tools, but since we are just trying to make the FPGA into an !OPenFlow switch, we skip over that section of the guide. cd into the NetFPGA directory, then make, make install, and reboot.
{{{
make
#a bunch of output showing status
make install
#more outputs
reboot
}}} 
after the machine has rebooted, check that drivers are loaded. The PID should show up:
{{{
[root@localhost ~]# /sbin/lsmod | grep nf2
nf2                    22540  0 
}}}
Finally, verify the interfaces with `/sbin/ifconfig -a` at the terminal. This is the output for our setup:
{{{
eth0      Link encap:Ethernet  HWaddr 00:1C:C0:B4:EC:D4  
          inet addr:192.168.202.102  Bcast:192.168.203.255  Mask:255.255.252.0
          inet6 addr: fe80::21c:c0ff:feb4:ecd4/64 Scope:Link
          UP BROADCAST RUNNING MULTICAST  MTU:1500  Metric:1
          RX packets:825 errors:0 dropped:0 overruns:0 frame:0
          TX packets:212 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:76080 (74.2 KiB)  TX bytes:21489 (20.9 KiB)
          Interrupt:50 Base address:0xa000 

lo        Link encap:Local Loopback  
          inet addr:127.0.0.1  Mask:255.0.0.0
          inet6 addr: ::1/128 Scope:Host
          UP LOOPBACK RUNNING  MTU:16436  Metric:1
          RX packets:1162 errors:0 dropped:0 overruns:0 frame:0
          TX packets:1162 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:2004680 (1.9 MiB)  TX bytes:2004680 (1.9 MiB)

nf2c0     Link encap:Ethernet  HWaddr 00:4E:46:32:43:00  
          BROADCAST MULTICAST  MTU:1986  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:58 

nf2c1     Link encap:Ethernet  HWaddr 00:4E:46:32:43:01  
          BROADCAST MULTICAST  MTU:1986  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:58 

nf2c2     Link encap:Ethernet  HWaddr 00:4E:46:32:43:02  
          BROADCAST MULTICAST  MTU:1986  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:58 

nf2c3     Link encap:Ethernet  HWaddr 00:4E:46:32:43:03  
          BROADCAST MULTICAST  MTU:1986  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:1000 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
          Interrupt:58 

sit0      Link encap:IPv6-in-IPv4  
          NOARP  MTU:1480  Metric:1
          RX packets:0 errors:0 dropped:0 overruns:0 frame:0
          TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
          collisions:0 txqueuelen:0 
          RX bytes:0 (0.0 b)  TX bytes:0 (0.0 b)
}}}  

== NetFPGA on Ubuntu (11/7) ==

Ultimately, the second NetFPGA host was built using Ubuntu 8.04 (kernel 2.6.24-16). To make things neat, user 'netfpga' was created for this process. Make sure the user is added to the sudoers list.  

=== installing NetFPGA drivers ===

First off, you need an account at netfpga.org to download the .tar files needed to install the netfpga drivers. The files needed are netfpga_base_beta_x_x.tar.gz and netfpga_lib.tar.gz. With an account, they can be downloaded from here: http://netfpga.org/beta/distributions/

Untar and the files with `tar -xvf <filename>`. They will untar into one directory called ''NF2''. Do not make and install yet - At this point, follow the directions on the [http://www.netfpga.org/netfpgawiki/index.php/Ubuntu_Compatibility Ubuntu compatibility] page. They ask you to make a few changes on the files located in NF2. A few things to note regarding the directions:

 * to edit /boot/grub/menu.lst as per the instructions, use the directions for modifying grub.conf for CentOS, found here: http://www.netfpga.org/netfpgawiki/index.php/Install_Software_1.0#CentOS_Installation_Instructions    

 * Environmental variables can be added by the command 
 {{{
 /usr/local/NF2/lib/scripts/user_account_setup/user_account_setup.pl
 }}} 
 as per the [http://netfpga.org/netfpgawiki/index.php/Guide#Verify_the_software_and_hardware Guide], however you might need to edit /usr/local/NF2 in user_account_setup.pl to specify the exact path to your NF2 directory:
{{{
else
{
  print "Copying the NF2 directory to your user account\n";
  `cp -r /home/netfpga/test/NF2 ~`;
}

print "Adding the NetFPGA Enviornment Variables to your .bashrc\n";
`cat /home/netfpga/test/NF2/bashrc_addon >> ~/.bashrc\n`;
}}}

Then you can make and install the drivers. Note, the selftest can't be run in Ubuntu. 

=== installing !OpenFlow on NetFPGA ===

General directions are found here: http://netfpga.org/netfpgawiki/index.php/OpenFlow-NetFPGA-090

In order to install !OpenFlow on the FPGA you need both the netFPGA !OpenFlow switch driver and the actual !OpenFlow software. 
 * netFPGA-OpenFLow-switch package : http://netfpga.org/beta/distributions/netfpga_openflow_switch.0_9_0-1.tar.gz (you need an account to access it)
 * !OpenFlow : use git (directions below)
  
Don't bother with the ./install.sh stuff under the '' Usage '' section of the directions found at netfpga.org, since they are custom-fitted for CentOS. Instead, the directions found at [http://openflowswitch.org/wk/index.php?title=CentOS_Install openflowswitch.org] should be referenced. The directions need to be modified slightly for Ubuntu:

1. ''' Install Dependencies '''

The following are needed to install everything properly (you should be able to `apt-get install` these):
 * git-core (recommended)
 * curl - dependency for Git that does not get installed properly due to a known bug in some versions of Ubuntu 
 * autoconf
 * automake 
 * libtool
 * gcc
 * pkg-config 

The stuff needed to build kernel modules:
 * linux-kernel-devel 
 * kernel-package
 * linux-libc-dev


2. ''' Install ''' [[BR]]
 
The commands, as per the CentOS install page at openflow.org:
{{{
git clone git://openflowswitch.org/openflow
cd openflow
./boot.sh
}}}
Reboot the machine, then build the kernel modules:
{{{
./configure --with-l26=/lib/modules/`uname -r`/build --enable-hw-tables=nf2
make
sudo make install
}}}

3. ''' Check that all is well/ the kernel modules exist: '''

the command
{{{
ls <path-to-your-openflow-directory>/datapath/linux-2.6 | grep ofdatapath
}}}
should bring up the following 2 things:
 * ofdatapath.ko
 * ofdatapath_netfpga.ko
 

== Regression testing ==
Connecting the SATA feedback loop seems to prevent the test from loading correctly, throwing the following error:
{{{
[root@localhost ~]# /root/NF2/lib/C/download/nf2_download ~/NF2/bitfiles/selftest.bit
Found net device: nf2c0
Bit file built from: nf2_top_par.ncd
Part: 2vp50ff1152
Date: 2008/ 7/21
Time: 17: 0:39
After resetting Programming interface, expected status to be 1 (FIFO empty).
However status & 0x102 is 0x102

Fatal Error, exiting...
}}}

 In addition, the Ethernet cables used for the cross-connection should be crossover, not straight through. Once the SATA cable was removed, and the test run with the command 
{{{
~/NF2/projects/selftest/sw/selftest -n
}}}
the proper output was returned. 

== Installing the !OpenFlow implementation (!OpenFlow-NetFPGA-090) ==   
After successfully installing the drivers, you can install the !OpenFlow switch with the following command:
{{{
[root@localhost ~]# yum install netfpga-openflow_switch
}}} 

= Setting up the NetFPGA host =
The goal of this project is to set up two NetFPGA hosts as !OpenFlow switches capable of tunneling. The hosts we are going to be using are the NetFPGA pre-built quad-core rack PCs ([http://www.accenttechnologyinc.com/product_info.php?products_id=5 found here]). Although the PC's come with CentOS pre-installed with the proper drivers needed for the NetFPGAs, we want to use Ubuntu. This section will document the steps needed to build a host running Ubuntu 9.10 Server Edition.

Note: We saved the HDD w/ CentOS that came with the PC. 

=== References ===
Following pages will be used to set the hosts up. 
 
 * NetFPGA Installation Guide : http://netfpga.org/foswiki/bin/view/NetFPGA/OneGig/Guide
 * NetFPGA Ubuntu compatibility page : http://netfpga.org/foswiki/bin/view/NetFPGA/OneGig/UbuntuCompatibility
 * !OpenFlow tunneling : http://netfpga.org/foswiki/bin/view/NetFPGA/OneGig/TunnelingOpenFlowNetFPGA090 
  
=== Host info ===

 * Distro used for PC: Ubuntu 9.10 Server Edition 32bit 
 * IPaddr: 192.168.203.187 (this is dynamic so it might change)
 * user: netfpga

== Setup Instructions == 
=== 1. Installing Ubuntu ===
1. Change boot priority of CD drive in BIOS - default will not let you boot into the install CD
 
2. Follow most of the defaults, except for the following: 
 * Disk partitioning - choose regular automatic partitioning  
 * When prompted with the option to install additional packages, install OpenSSH-server

3. Update packages 

4. Install dependencies for Ubuntu compatibility, as per the [http://netfpga.org/foswiki/bin/view/NetFPGA/OneGig/UbuntuCompatibility compatibility page]. The packages are:

  * build-essential
  * linux-headers-`uname -r`
  * ncurses-dev
  * libnet1-dev
  * libxml-simple-perl
  * libio-interface-perl
  * liblist-moreutils-perl
  * liberror-perl
  * sun-java6-jre
  * sun-java6-jdk
  * libpcap0.8
  * libpcap0.8-dev

== 2. Installing NetFPGA Drivers ==
Steps described by the NetFPGA tunneling page:
 1. Install base package
 2. Install !OpenFlow components

=== 1. Installing base package ===

1. Download the tarballs from http://netfpga.org/beta/distributions/  [[BR]]
For this you need a !FosWiki account (register [http://www.netfpga.org/foswiki/bin/view/System/UserRegistration?skin= here]). Download the newest netfpga_base_beta package (currently 2.0.0). Untar:
   
 tar -xvf netfpga_base_beta_2_0_0.tar.gz 
   
Untarring the package will create the directory NF2.  

2. Edit files/ symlinks as per compatibility page [[BR]]

Create links:
{{{
ln /usr/bin/lspci /sbin/lspci
ln /usr/bin/setpci /sbin/setpci
ln -s /usr/lib/libpcap.so.0.8 /usr/lib/libpcap.so.0.8.3
}}}

test_loopback_drop/run has been renamed run.pl in the most recent package. In this file you just need to change 'usleep 250' to 'sleep 0.00025'.  

NF2/lib/C/kernel/Makefile is already in working condition - you don't need to modify it. 

*Stopped at this point: The IRQF_SHARED flag is deprecated in kernels greater than 2.6.24. Instead, the SA_SHIRQ flag is used in include/linux/interrupt.h . in Ubuntu compatibility page**    


3. Edit and run user_account_setup.pl [[BR]]
The script sets environmental variables. It is located under /NF2/lib/scripts/user_account_setup/ . Running it as is will throw an error saying

 cat: /usr/local/NF2/bashrc_addon: No such file or directory   
 
The easiest thing to do is to edit the script to contain the exact path to your NF2 directory and bashrc_addon:
{{{
else
{
  print "Copying the NF2 directory to your user account\n";
  `cp -r /home/netfpga/NF2 ~`;
}

print "Adding the NetFPGA Enviornment Variables to your .bashrc\n";
`cat /home/netfpga/NF2/bashrc_addon >> ~/.bashrc\n`;
}}} 
Then it will run correctly (here NF2 is already in the home directory)
{{{
$ ./user_account_setup.pl NF2 directory already exists copy has been canceled
Adding the NetFPGA Enviornment Variables to your .bashrc
}}}